ABS-4L Series
Vertical Clamp/ Horizontal Injection
Standard Features:
- The hydraulic system operates with an energy saving regulating pump & proportional valve for drive & pressure regulation.
- Centrally applied high performance hydraulic mould clamping cylinder
- Linear transducer for clamping stroke with 1 mm accuracy.
- Mould closing & opening speed profiles, 4 stages programmable.
- Programmable closing & opening force.
- Intermediate stop possible with closing & opening.
- Monitoring of mould protection time.
- Hydraulic mould protection regulated.
- After alarm “Mould Protection” mould can either be stopped or opened.
- Hydraulic Ejector, Forces, Speeds, Advancement & Retraction delay as well as stroke count (up to 5) programmable.
- Modular injection unit as complete assembly group.
- Injection unit equipped with linear transducer of 1 mm accuracy.
- Four tie-bar type centrally fitted injection unit, vertical.
- Continuous nozzle contact during the complete cycle.
- Regulated injection speed profile, 5 steps programmable with injection delay.
- Measurement, display and monitoring of injection time.
- Switch over to holding pressure as a volume or time dependent function.
- Material cushioning monitoring.
- Screw circumferential speed display.
- Open nozzle with screw in tip.
- Electronically regulated cylinder and nozzle heating.
- Monitoring of oil temperature & filter contamination.
- Fine mesh oil filter in the return line.
- Temperature regulator with digital temperature input, integrated in the PLC.
- Temperature monitoring with tolerance band input regulation mode.
- Corrosion proof stainless steel material hopper with emptying position.
- Alarm for hopper emptying.
Regulated Parameters:
- Control Cabinet Temperature
- Hydraulic Oil Temperature
- Plasticizing Cylinder Temperature
- Screw RPM
- Screw Position
- Nozzle Contact Force
- Holding Pressure
- Back Pressure
- Movements and force of mould and ejector
- Ramp control sequence for mould and ejector end position
| ABS VV Series | Technical Data |
| Injection Unit | Unit | ABS VV-60 | ABS VV 100 | ABS VV 150 |
|---|---|---|---|---|
| Maximum Shot Weight | Gram | 60 | 100 | 150 |
| Screw Diameter | mm | 30 | 35 | 40 |
| Screw Stroke | mm | 90 | 135 | 165 |
| Injection Pressure | kg/cm2 | 1400 | 1300 | 1250 |
| Injection Rate | cm2/S | 40 | 73 | 119 |
| Temperature Control | Zone | 4 | 4 | 4 |
| Material Hopper Capacity | Liters | 8 | 10 | 10 |
| Clamping Unit | ||||
|---|---|---|---|---|
| Clamping Force | Ton | 25 | 40 | 70 |
| Opening Force | Ton | 7 | 9 | 14 |
| Mould Height (Minimum) | mm | 100 | 150 | 200 |
| Sliding Table Stroke (Optional) | mm | 350 | 400 | 500 |
| Opening Stroke | mm | 180 | 200 | 250 |
| Maximum Daylight | mm | 280 | 350 | 450 |
| Mould Dimensions | mm | 360×230 | 415×250 | 500×340 |
| Ejector Stroke | mm | 40 | 40 | 50 |
| Ejector Force | Ton | 1.3 | 1.3 | 2.5 |
| General | ||||
|---|---|---|---|---|
| Maximum Hy. Pressure | kg/cm² | 140 | 140 | 140 |
| Pump Output | L | 60 | 100 | 120 |
| Pump Motor Power | kW | 3.5 | 5 | 7.5 |
| Heating Capacity | kW | 2.7 | 3 | 4.5 |
| Total Wattage | kW | 6.2 | 8 | 12 |
| Heating Zone | Nos | 4 | 4 | 4 |
| Machine Weight (Approx) | kg | 1300 | 1650 | 2000 |
| Machine Size (LxWxH) | Inch | 75x36x108 | 80x40x108 | 85x44x112 |
