ABS-VV Series

view_video_butten

download_butten
Vertical Clamping / Vertical Screw

Standard Features:

Abs VV_Mail (4)

  • The hydraulic system operates with an energy saving regulating pump & proportional valve for drive & pressure regulation.
  • Centrally applied high performance hydraulic mould clamping cylinder
  • Linear transducer for clamping stroke with 1 mm accuracy.
  • Mould closing & opening speed profiles, 4 stages programmable.
  • Programmable closing & opening force.
  • Intermediate stop possible with closing & opening.
  • Monitoring of mould protection time.
  • Hydraulic mould protection regulated.
  • After alarm “Mould Protection” mould can either be stopped or opened.
  • Hydraulic Ejector, Forces, Speeds, Advancement & Retraction delay as well as stroke count (up to 5) programmable.
  • Modular injection unit as complete assembly group.
  • Injection unit equipped with linear transducer of 1 mm accuracy.
  • Four tie-bar type centrally fitted injection unit, vertical.
  • Continuous nozzle contact during the complete cycle.
  • Regulated injection speed profile, 5 steps programmable with injection delay.
  • Measurement, display and monitoring of injection time.
  • Switch over to holding pressure as a volume or time dependent function.
  • Material cushioning monitoring.
  • Screw circumferential speed display.
  • Open nozzle with screw in tip.
  • Electronically regulated cylinder and nozzle heating.
  • Monitoring of oil temperature & filter contamination.
  • Fine mesh oil filter in the return line.
  • Temperature regulator with digital temperature input, integrated in the PLC.
  • Temperature monitoring with tolerance band input regulation mode.
  • Corrosion proof stainless steel material hopper with emptying position.
  • Alarm for hopper emptying.

Regulated Parameters:

  • Control Cabinet Temperature
  • Hydraulic Oil Temperature
  • Plasticizing Cylinder Temperature
  • Screw RPM
  • Screw Position
  • Nozzle Contact Force
  • Holding Pressure
  • Back Pressure
  • Movements and force of mould and ejector
  • Ramp control sequence for mould and ejector end position
Machine Type Unit ABS VV 25 ABS VV 40 ABS VV 55  ABS VV 85
Screw Diameter mm 25 30 30 35 35 40 40 45
Injection Pressure kg/cm2 1678 1166 1784 1311 1858 1423 1423 1124
Theoretical Shot Volume cm3 44 71 71 110 110 166 223 275
Max.Shot Weight(PS) g 40 60 60 100 100 150 200 250
Injection Rate cm3/sec 35 50 52 71 69 90 107 135
Screw Speed Max. rpm 0-250 0-250 0-250 0-250
Nozzle Reaction Stroke mm 150 150 215 215
Number of Temperature Control - 3 4 4 5
Material Hopper Capacity l 8 10 10 20
Clamping Force tons 25 40 55 85
Opening Force tons 7.5 8.3 10 15
Mould Dimensions (L x W) mm 350 x 230 390 x 240 460 x 310 500 x 340
Min.Mold Height mm 100/150 150/200 150/200 200/250
Opening Stroke mm 200 200 200 250
Max.Open Daylight mm 300/350 350/400 350/400 450/500
Ejector Force tons 1.75 1.3 1.3 2.7
Ejector Stroke mm 50 50 50 70
Max.Hydraulic Pressure kg/cm2 140 140 140 140
Oil Reservoir Capacity liters 140 180 180 180
Pump Motor kW 3.7 5.5 5.5 11.1
Barrel Heating Power kW 2.7 4.7 5 5.3
Total Wattage kW 6.4 10.2 10.5 16.4
Machine Weight tons 1.25 1.8 2.3 2.6
Machine Dimensions (L x W x H) m 1.6 x 0.9 x 2.5 1.6 x 1.1 x 3.06 1.4 x 1.3 x 3.2 2 x 1.2 x 3.5